View and Download Kurzweil PC3 musician’s manual online. Kurzweil PC3: User Guide. PC3 Electronic Keyboard pdf manual download. Also for: Pc3x. View and Download Kurzweil PC3x service manual online. PC3x Synthesizer pdf manual download. Kurzweil┬«, and PC3┬« are trademarks of Young Chang Co., Ltd. All other products and brand names are trademarks or registered trademarks of their respective.

Author: Neran Terg
Country: China
Language: English (Spanish)
Genre: Software
Published (Last): 22 October 2011
Pages: 482
PDF File Size: 4.32 Mb
ePub File Size: 17.97 Mb
ISBN: 276-9-32402-457-7
Downloads: 2030
Price: Free* [*Free Regsitration Required]
Uploader: Voodoocage

Connect the stranded wire cable from the Wheels Assembly to J The bottom line in the display shows the four test modes. Turn the power off and remove the power cord. The keyboard is secured to the bottom enclosure using twelve screws.

Tilt the PC3x up and install the six keyboard rear screws.

Kurzweil PC3 Musician’s Manual

Got it, continue to print. Be sure that the rubber key contacts line up properly through the holes in the keyboard chassis. Note Start the sample will begin at the pre-set alternate start point in this case, slightly past the initial chiff. Do not use this apparatus near water. Follow the procedure described on page to remove the Connector Board.

Be sure the blue xD Daughtercard bezel is seated in the rear panel cutout properly. Hook the front end of the key under the keyboard chassis. Audio Output If the diagnostic version is 0. Comments manuao this Manuals Your Name. To print the kurzwsil completely, please, download it. Also See for PC3x Musician’s manual – pages Getting started manual – pages Getting started manual – pages. Chapter 2 Diagnostics The following lists the diagnostic tests available for the PC3x. To print the manual completely, please, download it.


The photo below shows the correct position for a 5 mm X 20 mm fuse. See Chapter 3, Page Two screws are longer than the others and have spacers located between the screw and the rear panel. Page What module do you want to update? Running ROM-based diagnostics 4. The enclosure support wall, transformer and AC recptacle are also included on the top enclosure. Got it, continue to print.

Diagnostics Description of Tests Notes 1. Align the center screw hole on the front panel edge with the thread marks in the extrusion and install the three screws that secure the front panel edge. Wheels Assembly to the bottom enclosure. Removing the Battery The battery CR in the PC3x keyboard is mounted into a holder on the Engine Board and is accessible when the access panel is removed.

Updating Via Computer Chapter 1 Introduction This chapter provides the service technician with a layout of the front and rear panel features, as well as a brief explanation of their functions. Diagnostics Entering Diagnostics 3. Do not block any of the ventilation openings.


Place the Engine Board in position on the top enclosure. Be sure to have your work surface prepared. Page 58 System objects installed. Follow the procedure described on cp3 to remove the enclosure support wall. Removing the Wheels Assembly Page 23 Diagnostics Description of Tests Notes 1.


Arrows identify the locations of the twelve screws. Slide the PC3x forward so that you can install the six keyboard front screws.

Run the Scanner Tests. The normal Boot Loader menu should now be displayed. Turning clockwise should increase the numbers in order Kurzweil PC3 User Manual 96 pages. Remove the eight screws that secure the Connector Board to the rear panel.

If the tests pass, the problem is likely the result of a setting in the Control Setup. Entering the Boot Loader Apply power to the unit.

Align the pivot with the hole at the rear of the key. Power Problems If a unit set for V is plugged into V, the fuses will blow immediately but no damage should occur to the unit.

Replacing the Fuse Holder 1. Verify the placement of the key spring.