The Cisco ASR X Router offers embedded services for enterprise and service provider networks in a 2-rack unit (2RU) small form factor. It is integrated with. ASR X Router: Access product specifications, documents, downloads, Visio stencils, product images, and community content. Data sheet describes how the Cisco SPA/SIP portfolio offers a rich set of QoS features for premium service delivery.

Author: Vudomuro Jugrel
Country: French Guiana
Language: English (Spanish)
Genre: Photos
Published (Last): 15 November 2013
Pages: 191
PDF File Size: 1.11 Mb
ePub File Size: 4.59 Mb
ISBN: 225-5-67270-189-1
Downloads: 12543
Price: Free* [*Free Regsitration Required]
Uploader: Kaganris

Peer IP address — Unlike earlier versions where a problem 1020 one process could crash the whole system, this modular design should help contain faults. Actual performance vary depending on the following factors: Dynamic Routing router bgp bgp log-neighbor-changes neighbor The 2 VPN tunnels configuration example here is built based on the IPsec tunnel and BGP configuration illustrated above, can be axr to more tunnels if required.

Populate fields for at least one tunnel: To define the route priority run the below command. Using the gcloud command-line tool Create a custom VPC network.

Cisco ASR 1000 Series Aggregation Services Routers: What is an ASR Router?

They comprise the memory, hard disk, and USB flash memory token. This comprison show you the models. Certain services require only a right-to-use RTU license, whereas other services require both an RTU license and one or more number-of-sessions licenses. All the licenses on the Cisco ASR Series are honor-based, meaning that the licenses are not enforced through a product activation or license key.

To enable a set of required features, one of the following three technology packages is required: It can be configured with your choice of a 5-gigabyte per second or a gigabyte per second embedded services processor.

The Cisco ASR Series Routers carry a modular yet integrated design, so network operators can increase their network capacity and services without a hardware upgrade.


Certain services require only a right-to-use RTU license, whereas other services require both a RTU license and one or more number-of-sessions licenses. It consolidates up to customized packet-processor cores MHz to 1.

Check Eatasheet practices for further recommendations on peer configurations. The upcoming section provide details to both in detail below:.

If an entire virtual device fails, Cloud VPN automatically instantiates a new one with the same configuration, so you don’t need to build two Cloud VPN gateways. You can repeat this command to add multiple ranges to the VPN tunnel.

They are the central control processors that run the network operating system, provide advanced routing capabilities, and also monitor and manage the other components of the Cisco ASR Series Aggregation Services Router.

The last date that support will be offered for the device, though, will be on July 31, Route processors provide advanced routing features and also monitor and manage other resources on the router. Remote network IP range — ELCs come in two different types: Based on the Aasr QuantumFlow Processor, the ESP performs forwarding, network security, deep packet inspection, firewalling, data center interconnect, and many other advanced features.

A sample interface configuration is datasheeet below for reference:. Except as otherwise noted, the content of this page is licensed under the Creative Commons Attribution 4. To increase the VPN throughput the recommendation is to add multiple Cloud VPN gateway on the same region to load balance the traffic datsheet the tunnels.

Previous post Next post. Service provider, enterprise network edge, etc. Association with the IPsec security association is done through the tunnel protection command. To ensure symmetry in your traffic flow, you can configure MED to influence the inbound traffic from Qsr for the same tunnel you are sending outbound traffic to. Note that lower the MED, higher the preference.

Because processing happens on a per-packet 1002, having a significant percentage of smaller packets can reduce overall throughput.


Cisco ASR Series Aggregation Services Routers Overview

Leave Local IP ranges blank except for the gateway’s subnet. It must belong to same subnet as the GCP-side interface. An IKEv2 policy with no proposal is considered incomplete. If you don’t have a static external IP address, you can create one by clicking New static IP address in the pull-down menu.

Cisco ASR 1002 Router Quick Start Guide

The following is a high-level overview of the configuration process which will datasheeg covered: Comment on this post. Use the static IP address vpn-static-ip you reserved earlier.

A tunnel interface is configured to be the logical interface associated with the tunnel. There are all kinds of news and information related to Cisco and Cisco network equipment, such as release of Cisco equipment, news of Cisco’s new networking solution, and Cisco hardware and software upgrading Environment overview The equipment used in the creation of this guide is as follows: The following is a high-level overview of the configuration process which will be covered:.

Make sure each tunnel has a unique pair of IPs. The upcoming section provide details to both in detail below: You can also use auto VPC network, make sure there is datawheet conflict with your local network range. Cisco ASRs consolidate these various traffic streams and apply traffic management and redundancy properties to them to maintain consistent performance among enterprise sites and cloud locations. Alternatively, you can leave –ip-address and –mask-length blank, and leave –peer-ip-address blank in the next step, and IP dstasheet will be automatically generated for you.

Request a Tutorial Ask for community help.