Flip, funnel or roll in any room of your house with the incredible Blade® Nano CP X. At just 29 grams (barely over an ounce), it’s the lightest flybarless CP heli in. WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem. Betrieb mit den Blade Nano CPS. Inklusive registrieren. Step by step DX6 / DX9 for nano This is done in the style from the DX6i for From the nano CPX manual the derives settings from DX8/DX18 are: .. you should see the blades twist and the swash move up and down level.
|Published (Last):||10 August 2013|
|PDF File Size:||20.2 Mb|
|ePub File Size:||20.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Adjusting the Drive Belt Tension Belt tension that is too tight results in loss of power and causes the belt to wear more quickly.
Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. Normal mode for takeoff lower rate then stunt 1 blaxe 2 are set higher respectfully. Horizon Hobby — China RoomNo. Do not ship LiPo batteries to Horizon.
Just bought my nano and will be setting it up tight.
BNF BLADE 3D INSTRUCTION MANUAL Pdf Download.
Can you upload the clx file? Now set Model Type. If you have already created curves and assigned them to other switch position, you can browse through them them 1,23, etc. Register Now In order to be able to post messages on the HeliFreak forums, you must first register.
Lower the throttle stick to the lowest position. If you want to check transmitter settings, you can go back through the menus, or use the monitor screen. Right now I am flying with this file: This is a request for a step by step guide to programming a DX6 for a nano.
Horizon reserves the right to change or modify this warranty at any time without notice. Table of Contents First Flight Preparation Please enter a valid email address for yourself. If you need to re-bind, follow the directions below.
Horizon Hobby Blade 200 SRX Instruction Manual
Thanks for the quick response and excellent explanation! A copy of your original sales receipt must be included for warranty consideration. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. If they do not move as shown, reverse the rudder channel in the transmitter refer to your transmitter manual for instructions.
Never leave the battery and charger unattended during the charge process.
BNF Blade 500 3D Instruction Manual
To fly or attempt to Turn on the DX6. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Page of 24 Go. Ensure correct model is namo on the DX6 screen this is why you gave it a name. This helicopter is equipped with anleitumg fiber blades that spin at very high RPM.
If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service.
You can also change the normal pitch curve to 30, 40, 50, 65, 80to make the pitch shifts not as agressive. Page of 18 Go. Before takeoff, I check the collective is responding, you should see the blades twist and anleitug swash move up and down level.
Switch H switch Throttle Hold to nnao. Others have had success using travel adjust for tame settings. Your RTF transmitter comes prebound to the model.
Horizon Product Support Fieldstone Road Champaign, Illinois Please call or e-mail us at productsupport horizonhobby.
HORIZON HOBBY BLADE SRX INSTRUCTION MANUAL Pdf Download.
Connect the flight battery to the ESC. Horizon Service Center Fieldstone Road Champaign, Illinois All other Products requiring warranty inspection or repair should be shipped bladd the following address: Move the rudder control to the right. Thank you so much for cp. Service or replacement decisions are at the sole discretion of Horizon. By pressing ‘print’ button you will print only current page. Use only Horizon Hobby approved battery packs and chargers compatible with this product.
Originally Posted by rammon3 Quote: Slowly increase the throttle until the model is approximately 2 ft. Maybe you figured it out, but for others having this issue Newbies guide to the DX6i for RC helicopters. Turn it off – again.